Cafe Nooner

409 Opera Aly, Eureka

Routine Inspection

ROACHY SAYS:

“Ooo! Welcome to Sanitarytown! Population: Cafe Nooner! I see lots of happy hungry mouths in this establishment's near future!!”

CP - Change of Ownership

ROACHY SAYS:

“Ooo! Welcome to Sanitarytown! Population: Cafe Nooner! I see lots of happy hungry mouths in this establishment's near future!!”

Reinspection

ROACHY SAYS:

“Both patrons and the health department agree! This place sets the standard for Humboldt food facility cleanliness! All hail Cafe Nooner!!”

Routine Inspection
08. Proper hot and cold holding temperatures.

Conditions Observed: Partially cooked fries awaiting fry were observed without temperature control on counter. This food requires temperature control or an approved time as a public health control procedure and time labeling. Place fries immediately under temperature control as a correction. Salad dressing with fresh garlic, oil and vinegar held without temperature control. Keep this item under temperature control at or below 41F. Uncooked bacon held at room temperature above 70F. Item discarded. Hold this food under 41F prior to cooking.

ROACHY SAYS:

“Except during preparation, cooking, cooling, transportation to or from a retail food facility for a period of less than thirty minutes, when time is used as the public health control, or as otherwise specified, potentially hazardous foods shall be maintained at or below 41F or at or above 135F. The following foods may be held at or below 45F: raw shell eggs, unshucked live molluscan shellfish, pasteurized milk and pasteurized milk products in original sealed containers, potentially hazardous foods held during transportation. Potentially hazardous foods held for dispensing in serving lines and salad bars may be held at 45F, not to exceed 12 hours in a 24 hour period, if unused portions are discarded. Food preparation shall not exceed two cumulative hours without a return to the required holding temperatures. (113996, 113998, 114037, 114343(a))”

15. Food contact surfaces: clean and sanitized.

Conditions Observed: Observed food handler clean the head of the mop in the middle bin of the three compartment sink while dishes were in the wash side and sanitizer was in the sani side. The handler didn’t immediately wash/rinse/sanitize this bin and there was residual oily buildup on sides. Due to a lack of a dedicated prep sink and dedicated janitorial sink, the three compartment sink is used for food prep and mop activities. It is imperative that mopping activities not occur in this location during food prep or utensil washing and that an adequate procedure is developed to ensure that the bins are washed and sanitized after each use for mopping and before using as a food prep sink. Installation of a dedicated janitorial sink should be a priority for this facility to minimize risk of cross contamination with mop activities. Facility fry cutter had heavy food buidup on both the cutter and press sections as well as what appeared to be old lubricant on the moving section of the base. Take unit apart before next use and wash/rinse/sanitize/remove buildup of food and lubricant on base. If lubricant is applied be sure it is food grade as it may contact potatoes. Wash/rinse/sanitize cutter and presser after each use. Repeat violation.

ROACHY SAYS:

“Food-contact surfaces and utensils shall be clean to sight and touch. Food-contact surfaces and multiservice utensils shall be effectively washed, rinsed, and sanitized to remove or completely loosen soils by use of manual or mechanical methods. Precleaning may be required. Manual sanitization shall be accomplished during the final rinse by contact with solution containing 100 ppm available chlorine, 200 ppm quaternary ammonium, or another approved sanitizer. Mechanical sanitization shall be accomplished in the final rinse by achieving a utensil surface temperature of 160F or by contact with solution containing 50 ppm available chlorine, 200 ppm quaternary ammonium, or another approved sanitizer. After cleaning and sanitizing, equipment and utensils shall be air dried. Mechancial warewash machines must be approved and installed and operated according to manufacturer's specifications. Food contact surfaces, utensils, and equipment shall be cleaned and sanitized at the following times: before each use with different type of raw food of animal origin, when changing from raw food to ready to eat food, between uses with raw produce and potentially hazardous food, before using a thermometer, and any time during the operation when contamination may have occurred. Warewash sinks used to wash wiping cloths, wash produce, or thaw food must be cleaned and sanitized before and after these uses. Equipment, food contact surfaces, and utensils must be cleaned and sanitized throughout the day at least every four hours or as needed to prevent contamination. (114097, 114099.1, 114099.2, 114099.4, 114099.6, 114099.7, 114101, 114105, 114109, 114111, 114113, 114115(a,c), 114117, 114125(b), 114141)”

Routine Inspection
12. Proper reheating procedures for hot holding.

Conditions Observed: Facility has policy for reheating of previously cooked and cooled foods prior to hot holding. Today, a soup was reheated but the final temperature did not reach the required temperature of 165 F. Soup measured at 158.5F. Verify final reheating temperatures on these reheated foods to ensure correct temperatures. Food was placed back on stove for continued reheat. Corrected.

ROACHY SAYS:

“Potentinally hazardous food that is cooked, cooled, and reheated for hot holding shall be heated to a temperature of 165F for 15 seconds. Cooked and refrigerated food that is prepared for immediate service in response to an individual consumer order may be served at any temperature. Reheating for hot holding shall be done rapidly, and the time between 41F and 165F shall not exceed two hours. Potentinally hazardous food reheated in a microwave oven for hot holding shall be rotated or stirred midway during cooking, covered to retain surface moisture, be reheated to 165F in all parts of the food, and stand covered for at least two minutes after reheating. Ready-to-eat food taken from a commercailly processed hermetically sealed container or from an intact package from a food processing plant shall be heated to a temperature of 135F for hot holding. (114014, 114016)”

15. Food contact surfaces: clean and sanitized.

Conditions Observed: Ice scoop tray had visible residue on surface. Cutting board and knife for lemons was not washed, rinsed, sanitized after use. Fry cutting tool was in place on wall with potato residue. Please remove this equipment to be sanitized after each use to ensure it is not inadvertently used unsanitized during later uses throughout the day.

ROACHY SAYS:

“Food-contact surfaces and utensils shall be clean to sight and touch. Food-contact surfaces and multiservice utensils shall be effectively washed, rinsed, and sanitized to remove or completely loosen soils by use of manual or mechanical methods. Precleaning may be required. Manual sanitization shall be accomplished during the final rinse by contact with solution containing 100 ppm available chlorine, 200 ppm quaternary ammonium, or another approved sanitizer. Mechanical sanitization shall be accomplished in the final rinse by achieving a utensil surface temperature of 160F or by contact with solution containing 50 ppm available chlorine, 200 ppm quaternary ammonium, or another approved sanitizer. After cleaning and sanitizing, equipment and utensils shall be air dried. Mechancial warewash machines must be approved and installed and operated according to manufacturer's specifications. Food contact surfaces, utensils, and equipment shall be cleaned and sanitized at the following times: before each use with different type of raw food of animal origin, when changing from raw food to ready to eat food, between uses with raw produce and potentially hazardous food, before using a thermometer, and any time during the operation when contamination may have occurred. Warewash sinks used to wash wiping cloths, wash produce, or thaw food must be cleaned and sanitized before and after these uses. Equipment, food contact surfaces, and utensils must be cleaned and sanitized throughout the day at least every four hours or as needed to prevent contamination. (114097, 114099.1, 114099.2, 114099.4, 114099.6, 114099.7, 114101, 114105, 114109, 114111, 114113, 114115(a,c), 114117, 114125(b), 114141)”

37. Equipment, utensils and linens: storage and use.

Conditions Observed: Observed clean single use hand towels stored in toilet room. Please move to alternate location to protect from potential contamination.

ROACHY SAYS:

“Clean equipment, utensils, linens, and single-use articles shall be stored at least six inches above the floor in an approved location within the fully enclosed permitted food facility. Clean equipment, utensils, linens, and single-use articles shall not be exposed to splash, dust, vermin, or other forms of contamination. Non-food items shall be stored and displayed separate from food and food-contact surfaces. During pauses in food preparation utensils shall be stored with handles above the top of the food, on a clean sanitized surface, in running water, or in water that is at least 135øF. Single-use articles and multiservice utensils shall be handled, displayed, and dispensed so that contamination of food and lip-contact surfaces is prevented. Extra preset tableware shall be removed when a consumer is seated or cleaned and sanitized before further use. Pressurized cylinders shall be securely fastened to rigid structure. Linens must be free of food residue and soil and be laundered as required. (114074, 114075(a,b,d,e), 114081, 114119, 114121, 114161, 114172, 114178, 114179, 114083, 114185, 114185.2, 114185.3, 114185.4, 114185.5)”

39. Thermometers provided and accurate.

Conditions Observed: Thermometer in beer cooler had inaccurate thermometer. Replace all improperly functioning thermometers. Be sure to calibrate probe type thermometers in ice bath frequently to ensure accuracy.

ROACHY SAYS:

“An accurate easily readable metal probe thermometer suitable for measuring temperature of food shall be available to the food handler. Thermometers shall be calibrated in accordance with manufacturer's specifications as necessary to ensure their accuracy. A thermometer +/- 2 degrees F shall be provided for all refrigerators, hot and cold holding units, and high temperature warewashing machines. (114157, 114159)”

48. Signs Posted, Last Inspection Report Available.

Conditions Observed: Facility permit is in hall adjacent to bathrooms. Please move to visible location in front of facility so that customers may see it upon entry. Cookline handwash lacks handwashing signage. Sign provided-please add to this location.

ROACHY SAYS:

“Handwashing signs directing employees to wash hands shall be posted in each toilet room used by food employees. No smoking signs shall be posted in food preparation, food storage, warewashing, and utensil storage areas. A copy of the most recent routine inspection report shall be maintained at the food facility and made available upon request. The food facility shall post a notice advising consumers that a copy of the most recent routine inspection report is available for review by any interested party. A permit shall be posted in a conspicuous place. (113725.1, 113953.5, 113978, 114381(e))”

Routine Inspection
08. Proper hot and cold holding temperatures.

Conditions Observed: Measured rice 104F with probe thermometer in hot hold unit. Observed hot hold unit requires water, and was empty during the inspection. Employee stated that she was heating the rice, to order, in a pan on the stove and the rice in the hot hold unit was not being used. Employee discarded approximately 2 cups of rice from hot hold unit and portioned rice from the refrigerator and reheated it on the stove when an order came in. Ensure if you are reheating for hot holding that you reheat on the stove or in the microwave to 165F prior to being put in the hot hold unit. This major violation was corrected on site, thank you.

ROACHY SAYS:

“Except during preparation, cooking, cooling, transportation to or from a retail food facility for a period of less than thirty minutes, when time is used as the public health control, or as otherwise specified, potentially hazardous foods shall be maintained at or below 41F or at or above 135F. The following foods may be held at or below 45F: raw shell eggs, unshucked live molluscan shellfish, pasteurized milk and pasteurized milk products in original sealed containers, potentially hazardous foods held during transportation. Potentially hazardous foods held for dispensing in serving lines and salad bars may be held at 45F, not to exceed 12 hours in a 24 hour period, if unused portions are discarded. Food preparation shall not exceed two cumulative hours without a return to the required holding temperatures. (113996, 113998, 114037, 114343(a))”

15. Food contact surfaces: clean and sanitized.

Conditions Observed: Measured chlorine sanitizer 0ppm in sanitizer bucket on 3 compartment sink. Measured various chlorine sanitizer solutions throughout the facility >100ppm. Use chlorine test strips each time sanitizer solution is made to ensure it is at the required concentration of 100ppm. Too little concentration will not sanitize properly, and too high of a concentration may be toxic. Employee changed chlorine sanitizer solution that measured 100ppm. This major violation was corrected on site, thank you.

ROACHY SAYS:

“Food-contact surfaces and utensils shall be clean to sight and touch. Food-contact surfaces and multiservice utensils shall be effectively washed, rinsed, and sanitized to remove or completely loosen soils by use of manual or mechanical methods. Precleaning may be required. Manual sanitization shall be accomplished during the final rinse by contact with solution containing 100 ppm available chlorine, 200 ppm quaternary ammonium, or another approved sanitizer. Mechanical sanitization shall be accomplished in the final rinse by achieving a utensil surface temperature of 160F or by contact with solution containing 50 ppm available chlorine, 200 ppm quaternary ammonium, or another approved sanitizer. After cleaning and sanitizing, equipment and utensils shall be air dried. Mechancial warewash machines must be approved and installed and operated according to manufacturer's specifications. Food contact surfaces, utensils, and equipment shall be cleaned and sanitized at the following times: before each use with different type of raw food of animal origin, when changing from raw food to ready to eat food, between uses with raw produce and potentially hazardous food, before using a thermometer, and any time during the operation when contamination may have occurred. Warewash sinks used to wash wiping cloths, wash produce, or thaw food must be cleaned and sanitized before and after these uses. Equipment, food contact surfaces, and utensils must be cleaned and sanitized throughout the day at least every four hours or as needed to prevent contamination. (114097, 114099.1, 114099.2, 114099.4, 114099.6, 114099.7, 114101, 114105, 114109, 114111, 114113, 114115(a,c), 114117, 114125(b), 114141)”

37. Equipment, utensils and linens: storage and use.

Conditions Observed: Observed clean towels stored in employee restroom. Find a sanitary location for storage of clean towels, away from the following locations: locker rooms, toilet rooms, refuse rooms, mechanical rooms, under sewer lines or leaking water lines, under open stairwells, under other sources of contamination. Employee moved towels to another location. This minor violation was corrected on site, thank you.

ROACHY SAYS:

“Clean equipment, utensils, linens, and single-use articles shall be stored at least six inches above the floor in an approved location within the fully enclosed permitted food facility. Clean equipment, utensils, linens, and single-use articles shall not be exposed to splash, dust, vermin, or other forms of contamination. Non-food items shall be stored and displayed separate from food and food-contact surfaces. During pauses in food preparation utensils shall be stored with handles above the top of the food, on a clean sanitized surface, in running water, or in water that is at least 135øF. Single-use articles and multiservice utensils shall be handled, displayed, and dispensed so that contamination of food and lip-contact surfaces is prevented. Extra preset tableware shall be removed when a consumer is seated or cleaned and sanitized before further use. Pressurized cylinders shall be securely fastened to rigid structure. Linens must be free of food residue and soil and be laundered as required. (114074, 114075(a,b,d,e), 114081, 114119, 114121, 114161, 114172, 114178, 114179, 114083, 114185, 114185.2, 114185.3, 114185.4, 114185.5)”

38. Adequate ventilation and lighting, designated areas, use.

Conditions Observed: Observed 2 non-functioning lights under ventilation hood. Replace light bulbs to provide adequate lighting.

ROACHY SAYS:

“Approved exhaust hoods shall be provided to remove toxic gases, heat, grease, vapors and smoke. Canopy-type hoods shall extend six inches beyond all cooking equipment. Toilet rooms shall be consistent with local building codes and vented to the outside air by a screened openable window, air shaft, or light-switch activated exhaust fan. Adequate lighting shall be provided in all areas to facilitate cleaning and inspection. Light fixtures in areas where open food is stored, served, prepared, and where utensils are washed shall be of shatterproof construction or protected with light shields. (114149, 114149.1, 114149.2, 114149.3, 114252, 114252.1)”

© 2021 Lost Coast Communications Contact: news@lostcoastoutpost.com.