Chevron - 6th St Mini-Mart
2480 6th St, Eureka
Tuesday, Nov. 16, 2021 (3 violations)
Routine Inspection
36. Equipment / Utensils approved; installed, clean, good repair, capacity.
Conditions Observed: Observed unclean, unused Turbo Chef oven in food prep area, and other unused equipment stored in the outside dumpster area. Remove unused and nonfunctional equipment from the premises. Observed ice buildup on bottom of True 2 door freezer. Maintain equipment clean and in good repair.
ROACHY SAYS:
“Utensils and equipment shall be kept fully operative and in good repair. All new and replacement equipment shall be properly installed and be certified or classified for sanitation by an ANSI accredited certification program. Electrical appliances must meet UL standards. Single-use articles shall not allow migration of deleterious substances or impart colors, odors, or tastes to food. Multi-use food contact surfaces must be smooth, free of breaks, chips, and similar imperfections; free of sharp internal angles, corners, and crevices; finished to have smooth welds and joints; be accessible for cleaning and inspection. Unless specified, wood and wood wicker may not be used as a food-contact surface. Unless specified, copper and copper alloys such as brass may not be used in contact with a food that has a pH below six or for a fitting between a backflow preventer and a carbonator. Beverage tubing and cold-plate beverage cooling devices cannot be installed in contact with stored ice intended to be used as food. Equipment that is not movable must be installed to allow for cleaning in place. Cutting or piercing parts of can openers must be readily removable. Facilities that wash, rinse, soak, thaw, or similarly prepare foods shall be provided with a approved food preparation sink. Reservoirs that supply water to produce foggers must be cleaned and maintained. Surfaces such as cutting blocks and boards that are subject to scratching and scoring shall be resurfaced or replaced if they can no longer be effectively cleaned and sanitized. (114130, 114130.1, 114130.2, 114130.3, 114130.4, 114130.5, 114130.6, 114132, 114133, 114137, 114139, 114153, 114163, 114165, 114167, 114169, 114175, 114177, 114180, 114182)”
45. Floor, walls, and ceilings: built, maintained, clean.
Conditions Observed: Observed floor coving is beginning to fail under the 3 compartment sink. Repair/replace coving to provide a surface that is smooth, durable, nonabsorbent and easy to clean.
ROACHY SAYS:
“Food facilities shall be fully enclosed in a building consisting of permanent floors, walls, and an overhead structure that meets minimum standards. The walls and ceiling shall be smooth, durable, nonabsorbent, and easily cleanable. Flooring and base coving shall be smooth, durable, and made of approved nonabsorbent material that is easily cleanable. Floor surfaces shall be coved at the juncture of the floor and wall with a 3/8 inch minimum radius and shall extend up the wall at least 4 inches. (114143(d), 114266, 114268, 114268.1, 114271, 114272)”
49. Plan Review.
Conditions Observed: Facility has remodeled (removed middle island counter, installed new counter tops and cabinets, relocated hot food cases and beverage/coffee equipment, removed front handwash sink). An existing facility that plans to remodel shall submit plans to this office for review and approval prior to purchasing and installing equipment, or making any changes to the existing food facility.
ROACHY SAYS:
“A person proposing to build or remodel a food facility shall submit complete, easily readable plans drawn to scale and specifications to the enforcement agency for review. Applicant shall receive plan approval before starting any new construction or remodeling of any facility for use as a retail food facility. Plans and specifications may also be required by the enforcement agency if the agency determines that they are necessary to assure compliance with the requirements of this part, including, but not limited to, a menu change or change in the facility's method of operation. (114380 (a, b))”
Thursday, April 22, 2021 (0 violations)
Routine Inspection
ROACHY SAYS:
“Huzzah! This establishment has successfully impressed the government! Kudos, Chevron - 6th St Mini-Mart!!”
Friday, Oct. 9, 2020 (2 violations)
Routine Inspection
15. Food contact surfaces: clean and sanitized.
Conditions Observed: Observed mold like substance in ice machine. Follow manufacturer’s instruction to clean and sanitize ice machine to prevent mold growth.
ROACHY SAYS:
“Food-contact surfaces and utensils shall be clean to sight and touch. Food-contact surfaces and multiservice utensils shall be effectively washed, rinsed, and sanitized to remove or completely loosen soils by use of manual or mechanical methods. Precleaning may be required. Manual sanitization shall be accomplished during the final rinse by contact with solution containing 100 ppm available chlorine, 200 ppm quaternary ammonium, or another approved sanitizer. Mechanical sanitization shall be accomplished in the final rinse by achieving a utensil surface temperature of 160F or by contact with solution containing 50 ppm available chlorine, 200 ppm quaternary ammonium, or another approved sanitizer. After cleaning and sanitizing, equipment and utensils shall be air dried. Mechancial warewash machines must be approved and installed and operated according to manufacturer's specifications. Food contact surfaces, utensils, and equipment shall be cleaned and sanitized at the following times: before each use with different type of raw food of animal origin, when changing from raw food to ready to eat food, between uses with raw produce and potentially hazardous food, before using a thermometer, and any time during the operation when contamination may have occurred. Warewash sinks used to wash wiping cloths, wash produce, or thaw food must be cleaned and sanitized before and after these uses. Equipment, food contact surfaces, and utensils must be cleaned and sanitized throughout the day at least every four hours or as needed to prevent contamination. (114097, 114099.1, 114099.2, 114099.4, 114099.6, 114099.7, 114101, 114105, 114109, 114111, 114113, 114115(a,c), 114117, 114125(b), 114141)”
37. Equipment, utensils and linens: storage and use.
Conditions Observed: Observed tools and other non-food items commingled with single-use hot dog wrappers and tissue paper on bottom shelf of prep table. Store tools in a location away from food and utensil storage and handling areas to prevent contamination.
ROACHY SAYS:
“Clean equipment, utensils, linens, and single-use articles shall be stored at least six inches above the floor in an approved location within the fully enclosed permitted food facility. Clean equipment, utensils, linens, and single-use articles shall not be exposed to splash, dust, vermin, or other forms of contamination. Non-food items shall be stored and displayed separate from food and food-contact surfaces. During pauses in food preparation utensils shall be stored with handles above the top of the food, on a clean sanitized surface, in running water, or in water that is at least 135øF. Single-use articles and multiservice utensils shall be handled, displayed, and dispensed so that contamination of food and lip-contact surfaces is prevented. Extra preset tableware shall be removed when a consumer is seated or cleaned and sanitized before further use. Pressurized cylinders shall be securely fastened to rigid structure. Linens must be free of food residue and soil and be laundered as required. (114074, 114075(a,b,d,e), 114081, 114119, 114121, 114161, 114172, 114178, 114179, 114083, 114185, 114185.2, 114185.3, 114185.4, 114185.5)”
Friday, Dec. 20, 2019 (6 violations)
Routine Inspection
08. Proper hot and cold holding temperatures.
Conditions Observed: Measured nacho cheese 130F with probe thermometer from the nacho cheese dispenser. Nacho cheese is a potentially hazardous food that must be held at or above 135F at all times. Operator discarded nacho cheese, thank you for correcting this major violation.
ROACHY SAYS:
“Except during preparation, cooking, cooling, transportation to or from a retail food facility for a period of less than thirty minutes, when time is used as the public health control, or as otherwise specified, potentially hazardous foods shall be maintained at or below 41F or at or above 135F. The following foods may be held at or below 45F: raw shell eggs, unshucked live molluscan shellfish, pasteurized milk and pasteurized milk products in original sealed containers, potentially hazardous foods held during transportation. Potentially hazardous foods held for dispensing in serving lines and salad bars may be held at 45F, not to exceed 12 hours in a 24 hour period, if unused portions are discarded. Food preparation shall not exceed two cumulative hours without a return to the required holding temperatures. (113996, 113998, 114037, 114343(a))”
15. Food contact surfaces: clean and sanitized.
Conditions Observed: Observed excessive buildup on nacho cheese dispenser. This is a food contact surface that must be washed, rinsed and sanitized at least every 4 hours to prevent cross-contamination. Due to the nacho cheese dispenser holding temperature at 130F, the nacho cheese dispenser was retired for the day. Wash, rinse and sanitize this piece of equipment prior to putting it back into service. This major violation was corrected on site, thank you.
ROACHY SAYS:
“Food-contact surfaces and utensils shall be clean to sight and touch. Food-contact surfaces and multiservice utensils shall be effectively washed, rinsed, and sanitized to remove or completely loosen soils by use of manual or mechanical methods. Precleaning may be required. Manual sanitization shall be accomplished during the final rinse by contact with solution containing 100 ppm available chlorine, 200 ppm quaternary ammonium, or another approved sanitizer. Mechanical sanitization shall be accomplished in the final rinse by achieving a utensil surface temperature of 160F or by contact with solution containing 50 ppm available chlorine, 200 ppm quaternary ammonium, or another approved sanitizer. After cleaning and sanitizing, equipment and utensils shall be air dried. Mechancial warewash machines must be approved and installed and operated according to manufacturer's specifications. Food contact surfaces, utensils, and equipment shall be cleaned and sanitized at the following times: before each use with different type of raw food of animal origin, when changing from raw food to ready to eat food, between uses with raw produce and potentially hazardous food, before using a thermometer, and any time during the operation when contamination may have occurred. Warewash sinks used to wash wiping cloths, wash produce, or thaw food must be cleaned and sanitized before and after these uses. Equipment, food contact surfaces, and utensils must be cleaned and sanitized throughout the day at least every four hours or as needed to prevent contamination. (114097, 114099.1, 114099.2, 114099.4, 114099.6, 114099.7, 114101, 114105, 114109, 114111, 114113, 114115(a,c), 114117, 114125(b), 114141)”
31. Food storage; food storage containers identified.
Conditions Observed: Observed nacho cheese bag in nacho cheese dispenser lacking a date code. Per manufacturer, the nacho cheese is only good for 5 days after it has been opened and put into the warmer. You are required to date the nacho cheese bag for 5 days, once opened. See California Department of Public Health Memorandum regarding nacho cheese warming units at retail locations. Operator removed nacho cheese bag from the dispenser. Observed nacho cheese was discolored and not dated. Operator discarded nacho cheese bag, thank you.
ROACHY SAYS:
“Adequate and suitable space shall be provided for the storage of food. Food shall be protected from contamination by storing the food in a clean, dry location, where it is not exposed to splash, dust, vermin, or other forms of contamination or adulteration, and at least six inches above the floor. Food shall not be stored in any of the following ways: in locker rooms, toilet rooms, dressing rooms, refuse rooms, mechanical rooms, under sewer lines that are not shielded to intercept potential drips, under leaking water lines, including leaking automatic fire sprinklers heads, or under lines on which water has condensated, under open stairwells or under sources of contamination. Working containers holding food or food ingredients that are removed from their original packages for use in the food facility shall be identified with the common name of the food. Non-prepackaged food may not be stored in direct contact with undrained ice. Products that are held by the permit holder for credit, redemption, or return to the distributor, such as damaged, spoiled, or recalled products shall be segregated and held in designated areas that are separated from food, equipment, utensils, linens, and single-use articles. (114047, 141049, 114051, 114053, 114055, 114067(h), 114069(b))”
36. Equipment / Utensils approved; installed, clean, good repair, capacity.
Conditions Observed: Observed pink slime-like substance in ice machine. Clean and sanitize ice machine per manufacturer instructions to prevent mold growth.
ROACHY SAYS:
“Utensils and equipment shall be kept fully operative and in good repair. All new and replacement equipment shall be properly installed and be certified or classified for sanitation by an ANSI accredited certification program. Electrical appliances must meet UL standards. Single-use articles shall not allow migration of deleterious substances or impart colors, odors, or tastes to food. Multi-use food contact surfaces must be smooth, free of breaks, chips, and similar imperfections; free of sharp internal angles, corners, and crevices; finished to have smooth welds and joints; be accessible for cleaning and inspection. Unless specified, wood and wood wicker may not be used as a food-contact surface. Unless specified, copper and copper alloys such as brass may not be used in contact with a food that has a pH below six or for a fitting between a backflow preventer and a carbonator. Beverage tubing and cold-plate beverage cooling devices cannot be installed in contact with stored ice intended to be used as food. Equipment that is not movable must be installed to allow for cleaning in place. Cutting or piercing parts of can openers must be readily removable. Facilities that wash, rinse, soak, thaw, or similarly prepare foods shall be provided with a approved food preparation sink. Reservoirs that supply water to produce foggers must be cleaned and maintained. Surfaces such as cutting blocks and boards that are subject to scratching and scoring shall be resurfaced or replaced if they can no longer be effectively cleaned and sanitized. (114130, 114130.1, 114130.2, 114130.3, 114130.4, 114130.5, 114130.6, 114132, 114133, 114137, 114139, 114153, 114163, 114165, 114167, 114169, 114175, 114177, 114180, 114182)”
37. Equipment, utensils and linens: storage and use.
Conditions Observed: Observed tongs stored on top of donut case. Provide a sanitary container for utensil storage. Observed tools and other non-food items commingled with single-use hot dog wrappers and tissue paper on bottom shelf of prep table. Store tools in a location away from food and utensil handling and storage areas to prevent contamination.
ROACHY SAYS:
“Clean equipment, utensils, linens, and single-use articles shall be stored at least six inches above the floor in an approved location within the fully enclosed permitted food facility. Clean equipment, utensils, linens, and single-use articles shall not be exposed to splash, dust, vermin, or other forms of contamination. Non-food items shall be stored and displayed separate from food and food-contact surfaces. During pauses in food preparation utensils shall be stored with handles above the top of the food, on a clean sanitized surface, in running water, or in water that is at least 135øF. Single-use articles and multiservice utensils shall be handled, displayed, and dispensed so that contamination of food and lip-contact surfaces is prevented. Extra preset tableware shall be removed when a consumer is seated or cleaned and sanitized before further use. Pressurized cylinders shall be securely fastened to rigid structure. Linens must be free of food residue and soil and be laundered as required. (114074, 114075(a,b,d,e), 114081, 114119, 114121, 114161, 114172, 114178, 114179, 114083, 114185, 114185.2, 114185.3, 114185.4, 114185.5)”
45. Floor, walls, and ceilings: built, maintained, clean.
Conditions Observed: Observed damaged floor in front of walk-in refrigerator. Repair/replace flooring to provide a surface that is smooth, durable, nonabsorbent and easy to clean with 3/8 inch radius coving that extends up the wall 4 inches.
ROACHY SAYS:
“Food facilities shall be fully enclosed in a building consisting of permanent floors, walls, and an overhead structure that meets minimum standards. The walls and ceiling shall be smooth, durable, nonabsorbent, and easily cleanable. Flooring and base coving shall be smooth, durable, and made of approved nonabsorbent material that is easily cleanable. Floor surfaces shall be coved at the juncture of the floor and wall with a 3/8 inch minimum radius and shall extend up the wall at least 4 inches. (114143(d), 114266, 114268, 114268.1, 114271, 114272)”
Wednesday, July 31, 2019 (0 violations)
Reinspection
ROACHY SAYS:
“Huzzah! This establishment has successfully impressed the government! Kudos, Chevron - 6th St Mini-Mart!!”
Friday, June 21, 2019 (6 violations)
Routine Inspection
08. Proper hot and cold holding temperatures.
Conditions Observed: Measured grilled chicken burrito 130.5F with probe thermometer in Aztec Grill hot hold unit. Observed the chicken burrito was stored on the edge of the rack, not in direct contact with heat source. Ensure burritos are in direct contact with heat source at all times. The burrito was discarded, thank you. Measured several items in new deli reach-in “island” refrigerator above 41F (chopped cantaloupe: 50F; chopped honeydew: 53F; tuna salad 43F; krispy chicken wrap: 42; wedge sandwich 48.5; BBQ chicken salad: 47.5F; chicken tenders 48F). Adjust/repair/replace this refrigerator to hold cold potentially hazardous foods at or below 41F at all times. Install readily visible thermometers in the front of top and middle shelf to monitor holding temperatures at all times. The cantaloupe and honeydew were discarded and all other foods were moved to the walk-in refrigerator holding at 41F. This is a major violation that will require a reinspection. Contact this office to schedule reinspection once this refrigerator has been adjusted or repaired.
ROACHY SAYS:
“Except during preparation, cooking, cooling, transportation to or from a retail food facility for a period of less than thirty minutes, when time is used as the public health control, or as otherwise specified, potentially hazardous foods shall be maintained at or below 41F or at or above 135F. The following foods may be held at or below 45F: raw shell eggs, unshucked live molluscan shellfish, pasteurized milk and pasteurized milk products in original sealed containers, potentially hazardous foods held during transportation. Potentially hazardous foods held for dispensing in serving lines and salad bars may be held at 45F, not to exceed 12 hours in a 24 hour period, if unused portions are discarded. Food preparation shall not exceed two cumulative hours without a return to the required holding temperatures. (113996, 113998, 114037, 114343(a))”
15. Food contact surfaces: clean and sanitized.
Conditions Observed: Measured QT sanitizer 0PPM in sanitizer bucket. Change the QT sanitizer when it becomes visibly soiled or falls below the required 200PPM. Employee refreshed QT sanitizer that measured 200PPM. Thank you for correcting this major violation.
ROACHY SAYS:
“Food-contact surfaces and utensils shall be clean to sight and touch. Food-contact surfaces and multiservice utensils shall be effectively washed, rinsed, and sanitized to remove or completely loosen soils by use of manual or mechanical methods. Precleaning may be required. Manual sanitization shall be accomplished during the final rinse by contact with solution containing 100 ppm available chlorine, 200 ppm quaternary ammonium, or another approved sanitizer. Mechanical sanitization shall be accomplished in the final rinse by achieving a utensil surface temperature of 160F or by contact with solution containing 50 ppm available chlorine, 200 ppm quaternary ammonium, or another approved sanitizer. After cleaning and sanitizing, equipment and utensils shall be air dried. Mechancial warewash machines must be approved and installed and operated according to manufacturer's specifications. Food contact surfaces, utensils, and equipment shall be cleaned and sanitized at the following times: before each use with different type of raw food of animal origin, when changing from raw food to ready to eat food, between uses with raw produce and potentially hazardous food, before using a thermometer, and any time during the operation when contamination may have occurred. Warewash sinks used to wash wiping cloths, wash produce, or thaw food must be cleaned and sanitized before and after these uses. Equipment, food contact surfaces, and utensils must be cleaned and sanitized throughout the day at least every four hours or as needed to prevent contamination. (114097, 114099.1, 114099.2, 114099.4, 114099.6, 114099.7, 114101, 114105, 114109, 114111, 114113, 114115(a,c), 114117, 114125(b), 114141)”
31. Food storage; food storage containers identified.
Conditions Observed: Observed nacho cheese bag in nacho cheese warmer/dispenser lacking a date code. Per manufacturer, the nacho cheese is only good for 5 days after it has been opened and put into the warmer. You are required to date the nacho cheese bag. Please instruct all employees on this procedure to ensure the nacho cheese is not sold past 5 days after opening. See California Department of Public Health (CDPH) Memorandum regarding nacho cheese warming units at retail locations for more information.
ROACHY SAYS:
“Adequate and suitable space shall be provided for the storage of food. Food shall be protected from contamination by storing the food in a clean, dry location, where it is not exposed to splash, dust, vermin, or other forms of contamination or adulteration, and at least six inches above the floor. Food shall not be stored in any of the following ways: in locker rooms, toilet rooms, dressing rooms, refuse rooms, mechanical rooms, under sewer lines that are not shielded to intercept potential drips, under leaking water lines, including leaking automatic fire sprinklers heads, or under lines on which water has condensated, under open stairwells or under sources of contamination. Working containers holding food or food ingredients that are removed from their original packages for use in the food facility shall be identified with the common name of the food. Non-prepackaged food may not be stored in direct contact with undrained ice. Products that are held by the permit holder for credit, redemption, or return to the distributor, such as damaged, spoiled, or recalled products shall be segregated and held in designated areas that are separated from food, equipment, utensils, linens, and single-use articles. (114047, 141049, 114051, 114053, 114055, 114067(h), 114069(b))”
34. Non-food-contact surfaces clean.
Conditions Observed: Observed non-food contact surfaces of equipment (exterior handle of Superior freezer, Icee machine, shelf under customer microwave, cappuccino machine) are visibly soiled. Clean non-food contact surfaces of equipment regularly to prevent buildup.
ROACHY SAYS:
“Nonfood-contact surfaces of equipment shall be kept free of an accumulation of dust, dirt, food residue, and other debris. (114115(b))”
36. Equipment / Utensils approved; installed, clean, good repair, capacity.
Conditions Observed: Observed nonfunctional 3 door Hussmann freezer on premises. Repair/replace/remove nonfunctional equipment from facility.
ROACHY SAYS:
“Utensils and equipment shall be kept fully operative and in good repair. All new and replacement equipment shall be properly installed and be certified or classified for sanitation by an ANSI accredited certification program. Electrical appliances must meet UL standards. Single-use articles shall not allow migration of deleterious substances or impart colors, odors, or tastes to food. Multi-use food contact surfaces must be smooth, free of breaks, chips, and similar imperfections; free of sharp internal angles, corners, and crevices; finished to have smooth welds and joints; be accessible for cleaning and inspection. Unless specified, wood and wood wicker may not be used as a food-contact surface. Unless specified, copper and copper alloys such as brass may not be used in contact with a food that has a pH below six or for a fitting between a backflow preventer and a carbonator. Beverage tubing and cold-plate beverage cooling devices cannot be installed in contact with stored ice intended to be used as food. Equipment that is not movable must be installed to allow for cleaning in place. Cutting or piercing parts of can openers must be readily removable. Facilities that wash, rinse, soak, thaw, or similarly prepare foods shall be provided with a approved food preparation sink. Reservoirs that supply water to produce foggers must be cleaned and maintained. Surfaces such as cutting blocks and boards that are subject to scratching and scoring shall be resurfaced or replaced if they can no longer be effectively cleaned and sanitized. (114130, 114130.1, 114130.2, 114130.3, 114130.4, 114130.5, 114130.6, 114132, 114133, 114137, 114139, 114153, 114163, 114165, 114167, 114169, 114175, 114177, 114180, 114182)”
45. Floor, walls, and ceilings: built, maintained, clean.
Conditions Observed: Observed hole in floor in front of walk-in refrigerator. Repair/replace floor to provide a surface that is smooth, durable, nonabsorbent and easy to clean with 3/8” radius that extends 4” up the wall. Submit spec sheets or floor samples to this office for approval prior to purchase and installation.
ROACHY SAYS:
“Food facilities shall be fully enclosed in a building consisting of permanent floors, walls, and an overhead structure that meets minimum standards. The walls and ceiling shall be smooth, durable, nonabsorbent, and easily cleanable. Flooring and base coving shall be smooth, durable, and made of approved nonabsorbent material that is easily cleanable. Floor surfaces shall be coved at the juncture of the floor and wall with a 3/8 inch minimum radius and shall extend up the wall at least 4 inches. (114143(d), 114266, 114268, 114268.1, 114271, 114272)”
Thursday, Dec. 13, 2018 (7 violations)
Routine Inspection
07. Adequate handwash facilities supplied and accessible.
Conditions Observed: Observed paper towel dispenser lacking paper towels at front handwash station. Keep handwash stations fully stocked, with required supplies in dispensers, at all times to properly wash hands.
ROACHY SAYS:
“Handwashing facilities shall be provided within or adjacent to toilet rooms, food preparation, and warewashing areas. Handwashing facilities shall be clean, unobstructed, and accessible at all times. Handwashing facilities shall be provided with soap and sanitary single use towels in approved dispensers. Dispensers shall be maintained in good repair. A handwashing facility shall not be used for purposes other than handwashing. (113953, 113953.1, 113953.2, 114067(f))”
30. Toxic substances properly identified, stored, used.
Conditions Observed: Observed unlabeled spray bottle, with other chemical storage, lacking a label. Label all chemicals when taken out of original manufacturer’s packaging for safety.
ROACHY SAYS:
“Only those insecticides, rodenticides, and other pesticides that are necessary, bear a legible manufacturer's label, and are specifically approved for use in a food facility may be used in a food facility in accordance with the manufacturer's instructions. Containers used for storing poisonous or toxic materiails such as cleaners and sanitizers taken from bulk supplies shall be clearly and individually identified with the common name of the material. Poisonous or toxic materials shall be stored or displayed to prevent contamination of food, equipment, utensils, linens, and single-use articles. (114254, 114254.1, 114254.2)”
34. Non-food-contact surfaces clean.
Conditions Observed: Observed underside of equipment is visibly soiled. Clean non-food contact surfaces of the equipment listed below: -coffee creamer dispenser -cappuccino machine -nacho cheese dispenser -Icee machine Observed food debris in microwave in back room. Clean non-food contact surfaces of equipment regularly to prevent buildup. Observed mold-like substance in floor sink under handwash sink & 3 compartment sink. Clean and sanitize floor sink to prevent mold-growth.
ROACHY SAYS:
“Nonfood-contact surfaces of equipment shall be kept free of an accumulation of dust, dirt, food residue, and other debris. (114115(b))”
36. Equipment / Utensils approved; installed, clean, good repair, capacity.
Conditions Observed: Observed Hussmann reach in refrigerator and 3 door glass freezer are non-functional. Repair, replace, or remove equipment from facility. Observed mold-like substance in interior of ice machine. Clean and sanitize ice machine per manufacturer’s instructions on inside panel. Keep this piece of equipment on a regular cleaning and maintenance schedule to prevent mold growth.
ROACHY SAYS:
“Utensils and equipment shall be kept fully operative and in good repair. All new and replacement equipment shall be properly installed and be certified or classified for sanitation by an ANSI accredited certification program. Electrical appliances must meet UL standards. Single-use articles shall not allow migration of deleterious substances or impart colors, odors, or tastes to food. Multi-use food contact surfaces must be smooth, free of breaks, chips, and similar imperfections; free of sharp internal angles, corners, and crevices; finished to have smooth welds and joints; be accessible for cleaning and inspection. Unless specified, wood and wood wicker may not be used as a food-contact surface. Unless specified, copper and copper alloys such as brass may not be used in contact with a food that has a pH below six or for a fitting between a backflow preventer and a carbonator. Beverage tubing and cold-plate beverage cooling devices cannot be installed in contact with stored ice intended to be used as food. Equipment that is not movable must be installed to allow for cleaning in place. Cutting or piercing parts of can openers must be readily removable. Facilities that wash, rinse, soak, thaw, or similarly prepare foods shall be provided with a approved food preparation sink. Reservoirs that supply water to produce foggers must be cleaned and maintained. Surfaces such as cutting blocks and boards that are subject to scratching and scoring shall be resurfaced or replaced if they can no longer be effectively cleaned and sanitized. (114130, 114130.1, 114130.2, 114130.3, 114130.4, 114130.5, 114130.6, 114132, 114133, 114137, 114139, 114153, 114163, 114165, 114167, 114169, 114175, 114177, 114180, 114182)”
38. Adequate ventilation and lighting, designated areas, use.
Conditions Observed: Observed non-functioning lights in the following areas: -back room in front of walk-in refrigerator -one restroom Repair/replace light bulbs to provide adequate lighting.
ROACHY SAYS:
“Approved exhaust hoods shall be provided to remove toxic gases, heat, grease, vapors and smoke. Canopy-type hoods shall extend six inches beyond all cooking equipment. Toilet rooms shall be consistent with local building codes and vented to the outside air by a screened openable window, air shaft, or light-switch activated exhaust fan. Adequate lighting shall be provided in all areas to facilitate cleaning and inspection. Light fixtures in areas where open food is stored, served, prepared, and where utensils are washed shall be of shatterproof construction or protected with light shields. (114149, 114149.1, 114149.2, 114149.3, 114252, 114252.1)”
45. Floor, walls, and ceilings: built, maintained, clean.
Conditions Observed: Observed floor is failing in front of walk-in refrigerator. Repair/replace floor to provide a surface that is smooth, durable, nonabsorbent, and easy to clean. Submit floor samples and/or manufacturer specification sheets to this office for approval prior to purchase and installation.
ROACHY SAYS:
“Food facilities shall be fully enclosed in a building consisting of permanent floors, walls, and an overhead structure that meets minimum standards. The walls and ceiling shall be smooth, durable, nonabsorbent, and easily cleanable. Flooring and base coving shall be smooth, durable, and made of approved nonabsorbent material that is easily cleanable. Floor surfaces shall be coved at the juncture of the floor and wall with a 3/8 inch minimum radius and shall extend up the wall at least 4 inches. (114143(d), 114266, 114268, 114268.1, 114271, 114272)”
50. Valid Facility Permit: expiration date, proper operation category.
Conditions Observed: The facility is currently chopping onions and holding them under temperature control for use as a condiment for hot dogs. The facility is currently operating under a minimal prep food permit, which does not include this practice. Immediately stop chopping onions and cold holding them for use as condiments on hot dogs. You may purchase pre-chopped onions and transfer them to the cold holding unit, or you may upgrade to a full-prep food permit if you choose to continue this practice. Contact this office for more information, if necessary.
ROACHY SAYS:
“A food facility shall not be open for business without a valid permit. Permit shall be posted in a conspicuous place within the food facility. (114067(b, c), 114381, 114387)”
CLICK TO MANAGE