Jambalaya

915 H St, Arcata

Routine Inspection
08. Proper hot and cold holding temperatures.

Conditions Observed: Measured minor temperature violations in the pizza prep today (mozzarella, 46 F; cheddar, 46 F). Adjust/service/repair to cold-hold all foods at 41 F or below. As discussed during the inspection, provide a new thermometer for this fridge.

ROACHY SAYS:

“Except during preparation, cooking, cooling, transportation to or from a retail food facility for a period of less than thirty minutes, when time is used as the public health control, or as otherwise specified, potentially hazardous foods shall be maintained at or below 41F or at or above 135F. The following foods may be held at or below 45F: raw shell eggs, unshucked live molluscan shellfish, pasteurized milk and pasteurized milk products in original sealed containers, potentially hazardous foods held during transportation. Potentially hazardous foods held for dispensing in serving lines and salad bars may be held at 45F, not to exceed 12 hours in a 24 hour period, if unused portions are discarded. Food preparation shall not exceed two cumulative hours without a return to the required holding temperatures. (113996, 113998, 114037, 114343(a))”

Routine Inspection
08. Proper hot and cold holding temperatures.

Conditions Observed: Measured foods in the left deli prep (pizza station) to be above 41 (cheese, 48 F, cheese, 47 F, olives, 44 F, cheese, 50 F, rice, 49 F). Adjust/service/repair to cold-hold at 41 F.

ROACHY SAYS:

“Except during preparation, cooking, cooling, transportation to or from a retail food facility for a period of less than thirty minutes, when time is used as the public health control, or as otherwise specified, potentially hazardous foods shall be maintained at or below 41F or at or above 135F. The following foods may be held at or below 45F: raw shell eggs, unshucked live molluscan shellfish, pasteurized milk and pasteurized milk products in original sealed containers, potentially hazardous foods held during transportation. Potentially hazardous foods held for dispensing in serving lines and salad bars may be held at 45F, not to exceed 12 hours in a 24 hour period, if unused portions are discarded. Food preparation shall not exceed two cumulative hours without a return to the required holding temperatures. (113996, 113998, 114037, 114343(a))”

10. Proper cooling methods.

Conditions Observed: Measured chicken wings in zip lock bag dated 10/14 to 62 F, 67 F, 57 F. PIC pulled to be discarded. Reviewed rapid cooling (using shallow metal containers, speedracks, etc). See regulation description. Develop a step-wise cooling procedure for all cook-and-chill foods that meets CalCode requirements to ensure that foods rapidly cool to 41 F. This violation requires a reinspection on/after 10/21/2020.

ROACHY SAYS:

“After heating, potentially hazardous foods shall be rapidly cooled from 135F to 70F within 2 hours, and then from 70F to 41F within 4 hours. Potentially hazardous foods prepared from ambient temperature ingredients must be cooled to below 41F within 4 hours. Cooling shall be facilitated by one or more of the following methods: in shallow pans, separating food into smaller portions, adding ice as an ingredient, using an ice bath and stirring frequently, using an ice paddle, using rapid cooling equipment, or using containers that facilitate heat transfer. (114002, 114002.1)”

37. Equipment, utensils and linens: storage and use.

Conditions Observed: Observed soda gun resting on top of ice used for beverages. Keep soda gun in holster and away from ice.

ROACHY SAYS:

“Clean equipment, utensils, linens, and single-use articles shall be stored at least six inches above the floor in an approved location within the fully enclosed permitted food facility. Clean equipment, utensils, linens, and single-use articles shall not be exposed to splash, dust, vermin, or other forms of contamination. Non-food items shall be stored and displayed separate from food and food-contact surfaces. During pauses in food preparation utensils shall be stored with handles above the top of the food, on a clean sanitized surface, in running water, or in water that is at least 135øF. Single-use articles and multiservice utensils shall be handled, displayed, and dispensed so that contamination of food and lip-contact surfaces is prevented. Extra preset tableware shall be removed when a consumer is seated or cleaned and sanitized before further use. Pressurized cylinders shall be securely fastened to rigid structure. Linens must be free of food residue and soil and be laundered as required. (114074, 114075(a,b,d,e), 114081, 114119, 114121, 114161, 114172, 114178, 114179, 114083, 114185, 114185.2, 114185.3, 114185.4, 114185.5)”

Reinspection

ROACHY SAYS:

“Wow! Roachy can see himself in your butterknives! Way to go, Jambalaya!!”

Routine Inspection
08. Proper hot and cold holding temperatures.

Conditions Observed: Measured foods with a metal stem thermometer in the right deli prep to be above 50 F. See measured observations. Observed thermometer in bottom of deli prep read 60 F. Instructed Operator to remove unit from service and discard all foods held in the unit overnight. Adjust/service/repair to cold-hold all foods at 41 F or below. Cook adjusted setting on unit - thank you. Consider having unit professionally serviced. This violation requires a reinspection prior to 6/12/2020. Measured foods in the top of the left deli prep to be above 41 F (cheese, 44 F; cheese, 45 F). As noted above, adjust/service/repair unit to keep all foods at or below 41 F.

ROACHY SAYS:

“Except during preparation, cooking, cooling, transportation to or from a retail food facility for a period of less than thirty minutes, when time is used as the public health control, or as otherwise specified, potentially hazardous foods shall be maintained at or below 41F or at or above 135F. The following foods may be held at or below 45F: raw shell eggs, unshucked live molluscan shellfish, pasteurized milk and pasteurized milk products in original sealed containers, potentially hazardous foods held during transportation. Potentially hazardous foods held for dispensing in serving lines and salad bars may be held at 45F, not to exceed 12 hours in a 24 hour period, if unused portions are discarded. Food preparation shall not exceed two cumulative hours without a return to the required holding temperatures. (113996, 113998, 114037, 114343(a))”

15. Food contact surfaces: clean and sanitized.

Conditions Observed: Observed food debris on interior of container at the end of dishwashing cycle. Discussed physically removing food debris, scraps prior to washing (CalCode 114099.1) Sanitizers are most effective when applied to a clean surface. Train staff and revise warewashing method to remove food debris prior to washing and sanitizing. See regulation description above. Observed minor grey-black build-up on front of divider in ice machine, and on bottom right hand side of divider. Remove build-up; clean and sanitize. As discussed during the inspection, increase frequency of deep cleaning for the ice machine (many units need to be cleaned weekly).

ROACHY SAYS:

“Food-contact surfaces and utensils shall be clean to sight and touch. Food-contact surfaces and multiservice utensils shall be effectively washed, rinsed, and sanitized to remove or completely loosen soils by use of manual or mechanical methods. Precleaning may be required. Manual sanitization shall be accomplished during the final rinse by contact with solution containing 100 ppm available chlorine, 200 ppm quaternary ammonium, or another approved sanitizer. Mechanical sanitization shall be accomplished in the final rinse by achieving a utensil surface temperature of 160F or by contact with solution containing 50 ppm available chlorine, 200 ppm quaternary ammonium, or another approved sanitizer. After cleaning and sanitizing, equipment and utensils shall be air dried. Mechancial warewash machines must be approved and installed and operated according to manufacturer's specifications. Food contact surfaces, utensils, and equipment shall be cleaned and sanitized at the following times: before each use with different type of raw food of animal origin, when changing from raw food to ready to eat food, between uses with raw produce and potentially hazardous food, before using a thermometer, and any time during the operation when contamination may have occurred. Warewash sinks used to wash wiping cloths, wash produce, or thaw food must be cleaned and sanitized before and after these uses. Equipment, food contact surfaces, and utensils must be cleaned and sanitized throughout the day at least every four hours or as needed to prevent contamination. (114097, 114099.1, 114099.2, 114099.4, 114099.6, 114099.7, 114101, 114105, 114109, 114111, 114113, 114115(a,c), 114117, 114125(b), 114141)”

28. Food separated and protected.

Conditions Observed: Observed two oranges to be covered in blue mold. Remove; inspect bulk foods frequently to ensure they are in good condition.

ROACHY SAYS:

“Food shall be protected from contamination during transportation, storage, preparation, holding, and display. Adequate and suitable counter space shall be provided for all food preparation. Food preparation shall be conducted wthin an approved food compartment or fully enclosed food facility. Open-air barbecues shall be separated from public access. (113984(a-f), 113986, 114060, 114067(a,d,e,j), 114069(a, c, d), 114077, 114089.1(c), 114143(c,e))”

CP - Change of Ownership
15. Food contact surfaces: clean and sanitized.

Conditions Observed: Observed minor black mildew-like build up on bottom and front of divider in ice machine. Showed observations to Owner. Reviewed cleaning-in-place. Remove build and sanitize routinely. Observed soda lines passing thru ice bin. Keep ice intended for consumption separate and away from the soda lines.

ROACHY SAYS:

“Food-contact surfaces and utensils shall be clean to sight and touch. Food-contact surfaces and multiservice utensils shall be effectively washed, rinsed, and sanitized to remove or completely loosen soils by use of manual or mechanical methods. Precleaning may be required. Manual sanitization shall be accomplished during the final rinse by contact with solution containing 100 ppm available chlorine, 200 ppm quaternary ammonium, or another approved sanitizer. Mechanical sanitization shall be accomplished in the final rinse by achieving a utensil surface temperature of 160F or by contact with solution containing 50 ppm available chlorine, 200 ppm quaternary ammonium, or another approved sanitizer. After cleaning and sanitizing, equipment and utensils shall be air dried. Mechancial warewash machines must be approved and installed and operated according to manufacturer's specifications. Food contact surfaces, utensils, and equipment shall be cleaned and sanitized at the following times: before each use with different type of raw food of animal origin, when changing from raw food to ready to eat food, between uses with raw produce and potentially hazardous food, before using a thermometer, and any time during the operation when contamination may have occurred. Warewash sinks used to wash wiping cloths, wash produce, or thaw food must be cleaned and sanitized before and after these uses. Equipment, food contact surfaces, and utensils must be cleaned and sanitized throughout the day at least every four hours or as needed to prevent contamination. (114097, 114099.1, 114099.2, 114099.4, 114099.6, 114099.7, 114101, 114105, 114109, 114111, 114113, 114115(a,c), 114117, 114125(b), 114141)”

34. Non-food-contact surfaces clean.

Conditions Observed: Observed excessive build-up in floor sink below 3-part sink. Remove build-up; clean and sanitize. Observed lingering build-up on FRP behind prep table. Maintain tidy surfaces.

ROACHY SAYS:

“Nonfood-contact surfaces of equipment shall be kept free of an accumulation of dust, dirt, food residue, and other debris. (114115(b))”

41. Plumbing: proper backflow devices.

Conditions Observed: Observed leak at hot water faucet at spray sink. Identify cause of leak and correct.

ROACHY SAYS:

“Steam tables, ice machines, ice bins, food preparation sinks, display cases, walk-in refrigeration units, and other similar equipment that discharge liquid waste shall drain into a floor sink with an air gap or other approved type of receptor. All plumbing and plumbing fixtures shall be installed in compliance with applicable local plumbing ordinances, maintained so as to prevent any contamination, kept clean, fully operative, and in good repair. The potable water supply shall be protected with a backflow or back siphonage protection device. Any hose used for potable water shall be of approved materials, labeled, properly stored, and used for no other purpose. Liquid drain lines shall not pass through an ice machine or an ice storage bin. (114171, 114190, 114192, 114193, 114193.1, 114199, 114201, 114269)”

45. Floor, walls, and ceilings: built, maintained, clean.

Conditions Observed: Observed a 2 by 3 inch gap in wall at base of doorway leaving dish pit. Repair wall to eliminate potential vermin harborage.

ROACHY SAYS:

“Food facilities shall be fully enclosed in a building consisting of permanent floors, walls, and an overhead structure that meets minimum standards. The walls and ceiling shall be smooth, durable, nonabsorbent, and easily cleanable. Flooring and base coving shall be smooth, durable, and made of approved nonabsorbent material that is easily cleanable. Floor surfaces shall be coved at the juncture of the floor and wall with a 3/8 inch minimum radius and shall extend up the wall at least 4 inches. (114143(d), 114266, 114268, 114268.1, 114271, 114272)”

Reinspection
15. Food contact surfaces: clean and sanitized.

Conditions Observed: Observed black, mildew like build-up on upper, back edges of ice machine. Remove build-up; clean and sanitize. See notes below.

ROACHY SAYS:

“Food-contact surfaces and utensils shall be clean to sight and touch. Food-contact surfaces and multiservice utensils shall be effectively washed, rinsed, and sanitized to remove or completely loosen soils by use of manual or mechanical methods. Precleaning may be required. Manual sanitization shall be accomplished during the final rinse by contact with solution containing 100 ppm available chlorine, 200 ppm quaternary ammonium, or another approved sanitizer. Mechanical sanitization shall be accomplished in the final rinse by achieving a utensil surface temperature of 160F or by contact with solution containing 50 ppm available chlorine, 200 ppm quaternary ammonium, or another approved sanitizer. After cleaning and sanitizing, equipment and utensils shall be air dried. Mechancial warewash machines must be approved and installed and operated according to manufacturer's specifications. Food contact surfaces, utensils, and equipment shall be cleaned and sanitized at the following times: before each use with different type of raw food of animal origin, when changing from raw food to ready to eat food, between uses with raw produce and potentially hazardous food, before using a thermometer, and any time during the operation when contamination may have occurred. Warewash sinks used to wash wiping cloths, wash produce, or thaw food must be cleaned and sanitized before and after these uses. Equipment, food contact surfaces, and utensils must be cleaned and sanitized throughout the day at least every four hours or as needed to prevent contamination. (114097, 114099.1, 114099.2, 114099.4, 114099.6, 114099.7, 114101, 114105, 114109, 114111, 114113, 114115(a,c), 114117, 114125(b), 114141)”

Routine Inspection
07. Adequate handwash facilities supplied and accessible.

Conditions Observed: No paper towels at handwash sink at the pizza bar. Operator provided paper towels. COS . Keep all handwashing sinks stocked with paper towels and pump soap at all times.

ROACHY SAYS:

“Handwashing facilities shall be provided within or adjacent to toilet rooms, food preparation, and warewashing areas. Handwashing facilities shall be clean, unobstructed, and accessible at all times. Handwashing facilities shall be provided with soap and sanitary single use towels in approved dispensers. Dispensers shall be maintained in good repair. A handwashing facility shall not be used for purposes other than handwashing. (113953, 113953.1, 113953.2, 114067(f))”

09. Time as public health control; procedures and records.

Conditions Observed: Observed pizza held at ambient temperature with no time labeling. Each pizza must be labeled with time at which it must be discarded or immediately consumed (i.e., four hour from when the pizza was removed from the oven. You must have a written procedure when using Time as Public Health Control. Train all staff in Time as Public Health Control. This violation requires a reinspection on/after 2/4/19.

ROACHY SAYS:

“When time as a public health control is used, the following procedures shall be observed: food items shall be marked to indicate four hours past the time when the food was removed from temperature control, food shall be served or discarded within the four hour time limit. Written procedures shall be maintained in the food facility and made available to the enforcement agency upon request, that ensure compliance with this section and section 114002, for food that is prepared, cooked, and refrigerated before time is used as a public health control. Time only may not be used in Licensed health care facilities, public school cafeterias, or private school cafeterias. (114000)”

14. Food in good condition; safe and unadulterated.

Conditions Observed: Observed excessive ice crystals and freezer burn on prepackaged carrots and veggie burgers in 2-door freezer. Discard impacted food. All food shall be in good condition. This violation requires a reinspection on/after 2/4/19.

ROACHY SAYS:

“Food shall be produced, prepared, stored, transported, and served so as to be free from adulteration and spoilage. Employees shall not commit any act that may cause the contamination or adulteration of food or food contact surfaces. Containers previously used to store poisonous or toxic materials shall not be used to store food, utensils, or single use articles. Utensils used for tasting shall be discarded or washed, rinsed, and sanitized between tastings. Ice used as a medium for cooling food and beverages shall not be offered for consumption. Food shall be inspected upon receipt and prior to any use, storage, or resale. Shell eggs shall be received clean, sound, and not exceed restricted tolerances for US Consumer Grade B Standards. (113967, 113976, 113980, 113982, 113988, 113990, 114035, 114041(a), 114254.3)”

15. Food contact surfaces: clean and sanitized.

Conditions Observed: No chlorine in dishwasher today. Adjust/service/repair to deliver chlorine at 50 PPM. Wash, rinse, and sanitize dishes manually until dishwasher is repaired. See sketch provided at the time of inspection. Observed excessive brown, mildew-like build-up on white divider in ice machine. Remove ice machine from service; discard ice and drain. Wash, rinse, and sanitize divider and ice machine. Observed black, mildew like build-up on soda lines in left ice bin at bar. Clean and sanitize lines. Consider keeping ice in a container that can be cleaned and sanitized. This violation requires a reinspection on/after 2/4/19.

ROACHY SAYS:

“Food-contact surfaces and utensils shall be clean to sight and touch. Food-contact surfaces and multiservice utensils shall be effectively washed, rinsed, and sanitized to remove or completely loosen soils by use of manual or mechanical methods. Precleaning may be required. Manual sanitization shall be accomplished during the final rinse by contact with solution containing 100 ppm available chlorine, 200 ppm quaternary ammonium, or another approved sanitizer. Mechanical sanitization shall be accomplished in the final rinse by achieving a utensil surface temperature of 160F or by contact with solution containing 50 ppm available chlorine, 200 ppm quaternary ammonium, or another approved sanitizer. After cleaning and sanitizing, equipment and utensils shall be air dried. Mechancial warewash machines must be approved and installed and operated according to manufacturer's specifications. Food contact surfaces, utensils, and equipment shall be cleaned and sanitized at the following times: before each use with different type of raw food of animal origin, when changing from raw food to ready to eat food, between uses with raw produce and potentially hazardous food, before using a thermometer, and any time during the operation when contamination may have occurred. Warewash sinks used to wash wiping cloths, wash produce, or thaw food must be cleaned and sanitized before and after these uses. Equipment, food contact surfaces, and utensils must be cleaned and sanitized throughout the day at least every four hours or as needed to prevent contamination. (114097, 114099.1, 114099.2, 114099.4, 114099.6, 114099.7, 114101, 114105, 114109, 114111, 114113, 114115(a,c), 114117, 114125(b), 114141)”

36. Equipment / Utensils approved; installed, clean, good repair, capacity.

Conditions Observed: Observed lids on deli prep at pizza bar to be in disrepair; observed standing water in bottom of deli prep. Observed excessive food debris in deli preps, on deli prep exteriors, and behind lids. Clean; remove build-up. Sanitize impacted surfaces.

ROACHY SAYS:

“Utensils and equipment shall be kept fully operative and in good repair. All new and replacement equipment shall be properly installed and be certified or classified for sanitation by an ANSI accredited certification program. Electrical appliances must meet UL standards. Single-use articles shall not allow migration of deleterious substances or impart colors, odors, or tastes to food. Multi-use food contact surfaces must be smooth, free of breaks, chips, and similar imperfections; free of sharp internal angles, corners, and crevices; finished to have smooth welds and joints; be accessible for cleaning and inspection. Unless specified, wood and wood wicker may not be used as a food-contact surface. Unless specified, copper and copper alloys such as brass may not be used in contact with a food that has a pH below six or for a fitting between a backflow preventer and a carbonator. Beverage tubing and cold-plate beverage cooling devices cannot be installed in contact with stored ice intended to be used as food. Equipment that is not movable must be installed to allow for cleaning in place. Cutting or piercing parts of can openers must be readily removable. Facilities that wash, rinse, soak, thaw, or similarly prepare foods shall be provided with a approved food preparation sink. Reservoirs that supply water to produce foggers must be cleaned and maintained. Surfaces such as cutting blocks and boards that are subject to scratching and scoring shall be resurfaced or replaced if they can no longer be effectively cleaned and sanitized. (114130, 114130.1, 114130.2, 114130.3, 114130.4, 114130.5, 114130.6, 114132, 114133, 114137, 114139, 114153, 114163, 114165, 114167, 114169, 114175, 114177, 114180, 114182)”

45. Floor, walls, and ceilings: built, maintained, clean.

Conditions Observed: Observed excessive build-up on wall behind butcher’s block, behind deli prep. Observed water pooling on floor in dishroom. Walls and floors shall be clean, smooth, durable and non-absorbent. Clean. Sanitize. Declutter. Observed food spill behind butchers’ block. Clean spills promptly to minimize vermin attraction.

ROACHY SAYS:

“Food facilities shall be fully enclosed in a building consisting of permanent floors, walls, and an overhead structure that meets minimum standards. The walls and ceiling shall be smooth, durable, nonabsorbent, and easily cleanable. Flooring and base coving shall be smooth, durable, and made of approved nonabsorbent material that is easily cleanable. Floor surfaces shall be coved at the juncture of the floor and wall with a 3/8 inch minimum radius and shall extend up the wall at least 4 inches. (114143(d), 114266, 114268, 114268.1, 114271, 114272)”

© 2020 Lost Coast Communications Contact: news@lostcoastoutpost.com.