Little Red Lion Cocktail Lounge

1506 5th St, Eureka

Reinspection

ROACHY SAYS:

“Wow! Roachy can see himself in your butterknives! Way to go, Little Red Lion Cocktail Lounge!!”

Routine Inspection
07. Adequate handwash facilities supplied and accessible.

Conditions Observed: Observed paper towels not stocked in the dispenser at handwash station. Keep required supplies stocked in dispensers at all times for proper handwashing. Employee stocked paper towels in the dispenser, this minor violation was corrected.

ROACHY SAYS:

“Handwashing facilities shall be provided within or adjacent to toilet rooms, food preparation, and warewashing areas. Handwashing facilities shall be clean, unobstructed, and accessible at all times. Handwashing facilities shall be provided with soap and sanitary single use towels in approved dispensers. Dispensers shall be maintained in good repair. A handwashing facility shall not be used for purposes other than handwashing. (113953, 113953.1, 113953.2, 114067(f))”

08. Proper hot and cold holding temperatures.

Conditions Observed: Measured ambient air 44.5F in small counter top refrigerator. Observed on manufacturer’s label inside of unit, “This equipment is intended for the storage and display of packaged products only.” Facility is holding potentially hazardous foods (open juices, mixers, 1/2 & 1/2, etc.) in this unit. Replace this refrigerator with a commercial refrigerator designed to hold potentially hazardous foods that is capable of holding cold temperatures at or below 41F at all times. Submit spec sheets for proposed refrigerator to this office for approval prior to purchase and installation.

ROACHY SAYS:

“Except during preparation, cooking, cooling, transportation to or from a retail food facility for a period of less than thirty minutes, when time is used as the public health control, or as otherwise specified, potentially hazardous foods shall be maintained at or below 41F or at or above 135F. The following foods may be held at or below 45F: raw shell eggs, unshucked live molluscan shellfish, pasteurized milk and pasteurized milk products in original sealed containers, potentially hazardous foods held during transportation. Potentially hazardous foods held for dispensing in serving lines and salad bars may be held at 45F, not to exceed 12 hours in a 24 hour period, if unused portions are discarded. Food preparation shall not exceed two cumulative hours without a return to the required holding temperatures. (113996, 113998, 114037, 114343(a))”

15. Food contact surfaces: clean and sanitized.

Conditions Observed: Observed mold-like substance in ice machine. Clean and sanitize ice machine per manufacturer’s instructions to prevent mold growth. Instructed employee to take ice machine out of service until it is clean and sanitized. Employee purchased pre-bagged ice from the liquor store next door for drinks. This is a major violation that will require a reinspection on or after 2/3/20.

ROACHY SAYS:

“Food-contact surfaces and utensils shall be clean to sight and touch. Food-contact surfaces and multiservice utensils shall be effectively washed, rinsed, and sanitized to remove or completely loosen soils by use of manual or mechanical methods. Precleaning may be required. Manual sanitization shall be accomplished during the final rinse by contact with solution containing 100 ppm available chlorine, 200 ppm quaternary ammonium, or another approved sanitizer. Mechanical sanitization shall be accomplished in the final rinse by achieving a utensil surface temperature of 160F or by contact with solution containing 50 ppm available chlorine, 200 ppm quaternary ammonium, or another approved sanitizer. After cleaning and sanitizing, equipment and utensils shall be air dried. Mechancial warewash machines must be approved and installed and operated according to manufacturer's specifications. Food contact surfaces, utensils, and equipment shall be cleaned and sanitized at the following times: before each use with different type of raw food of animal origin, when changing from raw food to ready to eat food, between uses with raw produce and potentially hazardous food, before using a thermometer, and any time during the operation when contamination may have occurred. Warewash sinks used to wash wiping cloths, wash produce, or thaw food must be cleaned and sanitized before and after these uses. Equipment, food contact surfaces, and utensils must be cleaned and sanitized throughout the day at least every four hours or as needed to prevent contamination. (114097, 114099.1, 114099.2, 114099.4, 114099.6, 114099.7, 114101, 114105, 114109, 114111, 114113, 114115(a,c), 114117, 114125(b), 114141)”

30. Toxic substances properly identified, stored, used.

Conditions Observed: Observed unlabeled chemical spray bottle adjacent to handwash station, containing bleach. Label all chemicals when taken out of original manufacturer’s packaging for safety. Employee labeled spray bottle, this minor violation was corrected.

ROACHY SAYS:

“Only those insecticides, rodenticides, and other pesticides that are necessary, bear a legible manufacturer's label, and are specifically approved for use in a food facility may be used in a food facility in accordance with the manufacturer's instructions. Containers used for storing poisonous or toxic materiails such as cleaners and sanitizers taken from bulk supplies shall be clearly and individually identified with the common name of the material. Poisonous or toxic materials shall be stored or displayed to prevent contamination of food, equipment, utensils, linens, and single-use articles. (114254, 114254.1, 114254.2)”

35. Warewashing: installed, maintained, used, Adequate Means to measure sanitizer

Conditions Observed: Test strips were not on-site. Obtain QT test strips, store in a readily available location, and use each time QT sanitizer is made to verify it is at the correct concentration of 200-400PPM.

ROACHY SAYS:

“Facilities that prepare food shall be equipped with a manual warewashing sink that has at least three compartments with two integral metal drainboards, except as specified in 114099(c). A warewashing sink shall not be used for handwashing except as specified in 114125(a). Sink compartments shall be large enough to accommodate immersion of the largest equipment and utensils used. Testing materials shall be provided to adequately measure the applicable sanitization method used during manual or mechanical warewashing. (114067(f,g), 114099, 114099.3, 114099.5, 114101(a), 114101.1, 114101.2, 114103, 114107, 114125(a))”

37. Equipment, utensils and linens: storage and use.

Conditions Observed: Observed ice scoop stored on top of ice machine. Store the ice scoop utensil in a sanitary container to prevent contamination.

ROACHY SAYS:

“Clean equipment, utensils, linens, and single-use articles shall be stored at least six inches above the floor in an approved location within the fully enclosed permitted food facility. Clean equipment, utensils, linens, and single-use articles shall not be exposed to splash, dust, vermin, or other forms of contamination. Non-food items shall be stored and displayed separate from food and food-contact surfaces. During pauses in food preparation utensils shall be stored with handles above the top of the food, on a clean sanitized surface, in running water, or in water that is at least 135øF. Single-use articles and multiservice utensils shall be handled, displayed, and dispensed so that contamination of food and lip-contact surfaces is prevented. Extra preset tableware shall be removed when a consumer is seated or cleaned and sanitized before further use. Pressurized cylinders shall be securely fastened to rigid structure. Linens must be free of food residue and soil and be laundered as required. (114074, 114075(a,b,d,e), 114081, 114119, 114121, 114161, 114172, 114178, 114179, 114083, 114185, 114185.2, 114185.3, 114185.4, 114185.5)”

44. Premises; personal/cleaning items; vermin-proofing.

Conditions Observed: Observed front door and back door propped open over the duration of the inspection. Observed missing screen and open window in 1 restroom. The facility is to remain vermin proof at all times. Keep doors and windows closed, or install screens, to prevent entrance or harborage of animals, birds or vermin, including but not limited to, insects and rodents.

ROACHY SAYS:

“All premises of a food facility shall be kept clean, fully operative, and in good repair. The premise of a food facility shall be free of litter and items unnecessary to the operation of the facility. Areas designated for employees to eat and drink shall be located so that food, clean equipent and utensils, linens, and single-use articles are protected from contamination. Personal items shall be stored in a designated area to prevent contamination of food or utensils. Food prep sinks, warewashing sinks, and handwashing sinks shall not be used for the cleaning or maintenance of tools or cleaning supplies or to dispose of mop water and similar liquid wastes. A dedicated janitorial sink with a drain shall be provided and conveniently located. A separate room, area, or cabinet shall be provided for cleaning supplies. The facility shall be kept vermin proof. Insect electrocution devices shall retain the insect within the device and shall not be located over food or utensil handling areas. (114123, 114143(a, b), 114256, 114256.1, 114256.2, 114256.4, 114257, 114257.1, 114259, 114259.2, 114259.3, 114279, 114281, 114282)”

Routine Inspection
34. Non-food-contact surfaces clean.

Conditions Observed: Observed standing liquid and mold-like substance in keg refrigerator. Clean and sanitize impacted area regularly to prevent mold growth.

ROACHY SAYS:

“Nonfood-contact surfaces of equipment shall be kept free of an accumulation of dust, dirt, food residue, and other debris. (114115(b))”

36. Equipment / Utensils approved; installed, clean, good repair, capacity.

Conditions Observed: Observed mold like substance in ice machine and on soda gun and holster. Clean and sanitize ice machine per manufacturer’s instructions and keep on a regular cleaning and maintenance schedule to prevent mold growth. Bartender sanitized soiled soda gun and holster. Please clean and sanitize soda gun and holster regularly to prevent mold growth.

ROACHY SAYS:

“Utensils and equipment shall be kept fully operative and in good repair. All new and replacement equipment shall be properly installed and be certified or classified for sanitation by an ANSI accredited certification program. Electrical appliances must meet UL standards. Single-use articles shall not allow migration of deleterious substances or impart colors, odors, or tastes to food. Multi-use food contact surfaces must be smooth, free of breaks, chips, and similar imperfections; free of sharp internal angles, corners, and crevices; finished to have smooth welds and joints; be accessible for cleaning and inspection. Unless specified, wood and wood wicker may not be used as a food-contact surface. Unless specified, copper and copper alloys such as brass may not be used in contact with a food that has a pH below six or for a fitting between a backflow preventer and a carbonator. Beverage tubing and cold-plate beverage cooling devices cannot be installed in contact with stored ice intended to be used as food. Equipment that is not movable must be installed to allow for cleaning in place. Cutting or piercing parts of can openers must be readily removable. Facilities that wash, rinse, soak, thaw, or similarly prepare foods shall be provided with a approved food preparation sink. Reservoirs that supply water to produce foggers must be cleaned and maintained. Surfaces such as cutting blocks and boards that are subject to scratching and scoring shall be resurfaced or replaced if they can no longer be effectively cleaned and sanitized. (114130, 114130.1, 114130.2, 114130.3, 114130.4, 114130.5, 114130.6, 114132, 114133, 114137, 114139, 114153, 114163, 114165, 114167, 114169, 114175, 114177, 114180, 114182)”

37. Equipment, utensils and linens: storage and use.

Conditions Observed: Observed ice scoop utensil stored on top of ice machine. Provide a sanitary container for ice scoop utensil storage. Clean and sanitize ice scoop utensil and container regularly. Bartender provided a sanitary container for the ice scoop utensil. This minor violation was corrected on site.

ROACHY SAYS:

“Clean equipment, utensils, linens, and single-use articles shall be stored at least six inches above the floor in an approved location within the fully enclosed permitted food facility. Clean equipment, utensils, linens, and single-use articles shall not be exposed to splash, dust, vermin, or other forms of contamination. Non-food items shall be stored and displayed separate from food and food-contact surfaces. During pauses in food preparation utensils shall be stored with handles above the top of the food, on a clean sanitized surface, in running water, or in water that is at least 135øF. Single-use articles and multiservice utensils shall be handled, displayed, and dispensed so that contamination of food and lip-contact surfaces is prevented. Extra preset tableware shall be removed when a consumer is seated or cleaned and sanitized before further use. Pressurized cylinders shall be securely fastened to rigid structure. Linens must be free of food residue and soil and be laundered as required. (114074, 114075(a,b,d,e), 114081, 114119, 114121, 114161, 114172, 114178, 114179, 114083, 114185, 114185.2, 114185.3, 114185.4, 114185.5)”

44. Premises; personal/cleaning items; vermin-proofing.

Conditions Observed: Observed front door and back door propped open during the inspection. The facility is to remain vermin proof at all times. Keep doors and windows closed or install screens to prevent entrance or harborage of animals, birds, or vermin, including but not limited to, insects and rodents.

ROACHY SAYS:

“All premises of a food facility shall be kept clean, fully operative, and in good repair. The premise of a food facility shall be free of litter and items unnecessary to the operation of the facility. Areas designated for employees to eat and drink shall be located so that food, clean equipent and utensils, linens, and single-use articles are protected from contamination. Personal items shall be stored in a designated area to prevent contamination of food or utensils. Food prep sinks, warewashing sinks, and handwashing sinks shall not be used for the cleaning or maintenance of tools or cleaning supplies or to dispose of mop water and similar liquid wastes. A dedicated janitorial sink with a drain shall be provided and conveniently located. A separate room, area, or cabinet shall be provided for cleaning supplies. The facility shall be kept vermin proof. Insect electrocution devices shall retain the insect within the device and shall not be located over food or utensil handling areas. (114123, 114143(a, b), 114256, 114256.1, 114256.2, 114256.4, 114257, 114257.1, 114259, 114259.2, 114259.3, 114279, 114281, 114282)”

Reinspection

ROACHY SAYS:

“Huzzah! This establishment has successfully impressed the government! Kudos, Little Red Lion Cocktail Lounge!!”

Routine Inspection
15. Food contact surfaces: clean and sanitized.

Conditions Observed: Observed mold like substance in ice machine. Clean and sanitize ice machine, per manufacturer’s instructions, regularly to prevent mold growth. This is a major violation that will require a reinspection on or after Monday, 1/14/19.

ROACHY SAYS:

“Food-contact surfaces and utensils shall be clean to sight and touch. Food-contact surfaces and multiservice utensils shall be effectively washed, rinsed, and sanitized to remove or completely loosen soils by use of manual or mechanical methods. Precleaning may be required. Manual sanitization shall be accomplished during the final rinse by contact with solution containing 100 ppm available chlorine, 200 ppm quaternary ammonium, or another approved sanitizer. Mechanical sanitization shall be accomplished in the final rinse by achieving a utensil surface temperature of 160F or by contact with solution containing 50 ppm available chlorine, 200 ppm quaternary ammonium, or another approved sanitizer. After cleaning and sanitizing, equipment and utensils shall be air dried. Mechancial warewash machines must be approved and installed and operated according to manufacturer's specifications. Food contact surfaces, utensils, and equipment shall be cleaned and sanitized at the following times: before each use with different type of raw food of animal origin, when changing from raw food to ready to eat food, between uses with raw produce and potentially hazardous food, before using a thermometer, and any time during the operation when contamination may have occurred. Warewash sinks used to wash wiping cloths, wash produce, or thaw food must be cleaned and sanitized before and after these uses. Equipment, food contact surfaces, and utensils must be cleaned and sanitized throughout the day at least every four hours or as needed to prevent contamination. (114097, 114099.1, 114099.2, 114099.4, 114099.6, 114099.7, 114101, 114105, 114109, 114111, 114113, 114115(a,c), 114117, 114125(b), 114141)”

24. No rodents, insects, birds, or animals.

Conditions Observed: Observed approximately 25 cockroach carcasses in cabinet under handwash sink. Clean and sanitize impacted area and monitor for evidence of cockroach activity. Contact professional pest control service for assistance removing cockroaches from facility. Remove standing water, remove debris and deep clean behind the bar. This is a major violation that will require a reinspection on or after Monday, 1/14/19.

ROACHY SAYS:

“A food facility shall be kept free of vermin. Live animals are prohibited from food facilities except as specified in 114259.5. Food facility employees shall not care for or handle animals that may be present in the food facility. Food facility employees are required to wash their hands after handling or caring for fish in an aquarium and/or shellfish, or crustacea, in display tanks and as specified in 114259.4. (114259.1, 114259.4, 114259.5)”

36. Equipment / Utensils approved; installed, clean, good repair, capacity.

Conditions Observed: Observed unused equipment stored in facility adjacent to walk-in refrigerator. Repair/replace/remove unused equipment from facility. Observed mold-like substance in soda gun and soda gun holster. Clean and sanitize soda gun and soda gun holster every day to prevent mold growth. Recommend disassembling soda gun and submerging in water over night to remove soda residue and maintain clean.

ROACHY SAYS:

“Utensils and equipment shall be kept fully operative and in good repair. All new and replacement equipment shall be properly installed and be certified or classified for sanitation by an ANSI accredited certification program. Electrical appliances must meet UL standards. Single-use articles shall not allow migration of deleterious substances or impart colors, odors, or tastes to food. Multi-use food contact surfaces must be smooth, free of breaks, chips, and similar imperfections; free of sharp internal angles, corners, and crevices; finished to have smooth welds and joints; be accessible for cleaning and inspection. Unless specified, wood and wood wicker may not be used as a food-contact surface. Unless specified, copper and copper alloys such as brass may not be used in contact with a food that has a pH below six or for a fitting between a backflow preventer and a carbonator. Beverage tubing and cold-plate beverage cooling devices cannot be installed in contact with stored ice intended to be used as food. Equipment that is not movable must be installed to allow for cleaning in place. Cutting or piercing parts of can openers must be readily removable. Facilities that wash, rinse, soak, thaw, or similarly prepare foods shall be provided with a approved food preparation sink. Reservoirs that supply water to produce foggers must be cleaned and maintained. Surfaces such as cutting blocks and boards that are subject to scratching and scoring shall be resurfaced or replaced if they can no longer be effectively cleaned and sanitized. (114130, 114130.1, 114130.2, 114130.3, 114130.4, 114130.5, 114130.6, 114132, 114133, 114137, 114139, 114153, 114163, 114165, 114167, 114169, 114175, 114177, 114180, 114182)”

41. Plumbing: proper backflow devices.

Conditions Observed: Observed waste line from keg refrigerator draining into a Folgers coffee container. Equipment that discharges liquid waste shall drain by means of indirect waste pipes through an air gap into a floor sink or other approved receptor.

ROACHY SAYS:

“Steam tables, ice machines, ice bins, food preparation sinks, display cases, walk-in refrigeration units, and other similar equipment that discharge liquid waste shall drain into a floor sink with an air gap or other approved type of receptor. All plumbing and plumbing fixtures shall be installed in compliance with applicable local plumbing ordinances, maintained so as to prevent any contamination, kept clean, fully operative, and in good repair. The potable water supply shall be protected with a backflow or back siphonage protection device. Any hose used for potable water shall be of approved materials, labeled, properly stored, and used for no other purpose. Liquid drain lines shall not pass through an ice machine or an ice storage bin. (114171, 114190, 114192, 114193, 114193.1, 114199, 114201, 114269)”

45. Floor, walls, and ceilings: built, maintained, clean.

Conditions Observed: Observed the floor has been removed from behind the bar. You must conform to California Retail Food Code requirements and install flooring that is smooth, durable, nonabsorbent and easy to clean with a minimum 3/8 inch radius coving that extends at least 4 inches up the wall. Submit manufacturer specification sheets or samples for the flooring and coving to this office for approval prior to purchase and installation of floors/coving.

ROACHY SAYS:

“Food facilities shall be fully enclosed in a building consisting of permanent floors, walls, and an overhead structure that meets minimum standards. The walls and ceiling shall be smooth, durable, nonabsorbent, and easily cleanable. Flooring and base coving shall be smooth, durable, and made of approved nonabsorbent material that is easily cleanable. Floor surfaces shall be coved at the juncture of the floor and wall with a 3/8 inch minimum radius and shall extend up the wall at least 4 inches. (114143(d), 114266, 114268, 114268.1, 114271, 114272)”

© 2020 Lost Coast Communications Contact: news@lostcoastoutpost.com.