Z and J Asian Subs

2336 3rd St, Eureka

Routine Inspection
02. Food safety certification, food handler card compliance

Conditions Observed: Facility is lacking a Food Safety Manager (FSM). Obtain FSM certificate within 60 days and make available for observation during routine inspections.

ROACHY SAYS:

“Food facilities that prepare, handle, or serve non-prepackaged potentially hazardous food, shall have an owner or employee who has passed an aproved food safety certification examination. Food handlers that prepare, handle, or serve non-prepackaged potentially hazardous food, shall obtain a valid Food Handler Card within 30 days after date of hire. (113947.1-113947.5, 113948)”

06. Hands clean and properly washed; gloves used properly.

Conditions Observed: Observed employee change tasks from entering orders on the order screen at the service window to conducting food preparation to make a smoothie without handwashing. Handwashing is required when changing tasks, prior to preparing food and anytime in which the hands may become contaminated. Owner/operator instructed employee to wash their hands when changing tasks and prior to conducting food prep. Use the handout that was provided to train employees on handwashing requirements. Employee demonstrated active handwashing over the duration of the inspection.

ROACHY SAYS:

“Food employees shall minimize bare hand and arm contact with nonprepackaged food that is in ready to eat form. Whenever gloves are worn, they shall be changed, replaced, or washed as often as handwashing is required. Single-use gloves shall not be washed. Employees shall wash their hands in the following situations: immediately before engaging in food preparation including working with nonprepackaged food, clean equipment and utensils and unwrapped single-use food containers and utensils; after touching bare human body parts other than clean hands and clean exposed portions of arms; after using the toilet room; after caring for or handling any animal; after coughing, sneezing, using a handkerchief or disposable tissue, using tobacco, eating or drinking; after handling soiled equipment or utensils; during food preparation, as often as necessary to remove soil and contamination and to prevent cross-contamination when changing tasks; when switching from working with raw food and working with ready-to-eat foods; before initially donning gloves for working with food; before dispensing or serving food handling clean tableware and serving utensils in the food service area; after engaging in other activities that contaminate the hands. (113952, 113953.3, 113953.4, 113961, 113968, 113973)”

36. Equipment / Utensils approved; installed, clean, good repair, capacity.

Conditions Observed: Observed food debris on interior of ice chest that is used to store ice. Maintain equipment clean.

ROACHY SAYS:

“Utensils and equipment shall be kept fully operative and in good repair. All new and replacement equipment shall be properly installed and be certified or classified for sanitation by an ANSI accredited certification program. Electrical appliances must meet UL standards. Single-use articles shall not allow migration of deleterious substances or impart colors, odors, or tastes to food. Multi-use food contact surfaces must be smooth, free of breaks, chips, and similar imperfections; free of sharp internal angles, corners, and crevices; finished to have smooth welds and joints; be accessible for cleaning and inspection. Unless specified, wood and wood wicker may not be used as a food-contact surface. Unless specified, copper and copper alloys such as brass may not be used in contact with a food that has a pH below six or for a fitting between a backflow preventer and a carbonator. Beverage tubing and cold-plate beverage cooling devices cannot be installed in contact with stored ice intended to be used as food. Equipment that is not movable must be installed to allow for cleaning in place. Cutting or piercing parts of can openers must be readily removable. Facilities that wash, rinse, soak, thaw, or similarly prepare foods shall be provided with a approved food preparation sink. Reservoirs that supply water to produce foggers must be cleaned and maintained. Surfaces such as cutting blocks and boards that are subject to scratching and scoring shall be resurfaced or replaced if they can no longer be effectively cleaned and sanitized. (114130, 114130.1, 114130.2, 114130.3, 114130.4, 114130.5, 114130.6, 114132, 114133, 114137, 114139, 114153, 114163, 114165, 114167, 114169, 114175, 114177, 114180, 114182)”

45. Floor, walls, and ceilings: built, maintained, clean.

Conditions Observed: Observed floors and coving are failing throughout the facility. Repair/replace floors to provide a surface that is smooth, durable, nonabsorbent and easy to clean with minimum 3/8” radius coving that extends up the wall at least 4 inches.

ROACHY SAYS:

“Food facilities shall be fully enclosed in a building consisting of permanent floors, walls, and an overhead structure that meets minimum standards. The walls and ceiling shall be smooth, durable, nonabsorbent, and easily cleanable. Flooring and base coving shall be smooth, durable, and made of approved nonabsorbent material that is easily cleanable. Floor surfaces shall be coved at the juncture of the floor and wall with a 3/8 inch minimum radius and shall extend up the wall at least 4 inches. (114143(d), 114266, 114268, 114268.1, 114271, 114272)”

Routine Inspection
02. Food safety certification, food handler card compliance

Conditions Observed: Facility is lacking a Food Safety Manager (FSM). Obtain FSM certificate and keep on file at the facility for review during routine inspections.

ROACHY SAYS:

“Food facilities that prepare, handle, or serve non-prepackaged potentially hazardous food, shall have an owner or employee who has passed an aproved food safety certification examination. Food handlers that prepare, handle, or serve non-prepackaged potentially hazardous food, shall obtain a valid Food Handler Card within 30 days after date of hire. (113947.1-113947.5, 113948)”

45. Floor, walls, and ceilings: built, maintained, clean.

Conditions Observed: Observed floors and coving are failing throughout. Replace floors to provide a smooth surface that is nonabsorbent, durable and easy to clean with minimum 3/8” radius coving that extends up the wall at least 4 inches. Submit spec sheets or floor samples to this office for approval prior to purchase and installation.

ROACHY SAYS:

“Food facilities shall be fully enclosed in a building consisting of permanent floors, walls, and an overhead structure that meets minimum standards. The walls and ceiling shall be smooth, durable, nonabsorbent, and easily cleanable. Flooring and base coving shall be smooth, durable, and made of approved nonabsorbent material that is easily cleanable. Floor surfaces shall be coved at the juncture of the floor and wall with a 3/8 inch minimum radius and shall extend up the wall at least 4 inches. (114143(d), 114266, 114268, 114268.1, 114271, 114272)”

Routine Inspection

ROACHY SAYS:

“Humboldt foodies rejoice! Our reports show that Z and J Asian Subs knows how to get you fed in a sanitary manner. Now that's nummy!!”

Routine Inspection

ROACHY SAYS:

“Both patrons and the health department agree! This place sets the standard for Humboldt food facility cleanliness! All hail Z and J Asian Subs!!”

Routine Inspection
45. Floor, walls, and ceilings: built, maintained, clean.

Conditions Observed: Observed floors and coving have failed throughout the facility. Replace floors to provide a surface that is smooth, durable, nonabsorbent and easy to clean with 3/8 inch radius coving that extends up the wall 4 inches. Submit floor samples or spec sheets to this office for approval prior to purchase and installation.

ROACHY SAYS:

“Food facilities shall be fully enclosed in a building consisting of permanent floors, walls, and an overhead structure that meets minimum standards. The walls and ceiling shall be smooth, durable, nonabsorbent, and easily cleanable. Flooring and base coving shall be smooth, durable, and made of approved nonabsorbent material that is easily cleanable. Floor surfaces shall be coved at the juncture of the floor and wall with a 3/8 inch minimum radius and shall extend up the wall at least 4 inches. (114143(d), 114266, 114268, 114268.1, 114271, 114272)”

48. Signs Posted, Last Inspection Report Available.

Conditions Observed: Observed expired food permit hung in facility. Hang current food permit. Contact this office if you need a duplicate copy.

ROACHY SAYS:

“Handwashing signs directing employees to wash hands shall be posted in each toilet room used by food employees. No smoking signs shall be posted in food preparation, food storage, warewashing, and utensil storage areas. A copy of the most recent routine inspection report shall be maintained at the food facility and made available upon request. The food facility shall post a notice advising consumers that a copy of the most recent routine inspection report is available for review by any interested party. A permit shall be posted in a conspicuous place. (113725.1, 113953.5, 113978, 114381(e))”

Routine Inspection
28. Food separated and protected.

Conditions Observed: Observed open bag of bulk sugar on storage shelf. Once a bulk bag of food is opened, transfer it to a rigid container with a tight fitting lid to prevent contamination or potentially vermin attraction.

ROACHY SAYS:

“Food shall be protected from contamination during transportation, storage, preparation, holding, and display. Adequate and suitable counter space shall be provided for all food preparation. Food preparation shall be conducted wthin an approved food compartment or fully enclosed food facility. Open-air barbecues shall be separated from public access. (113984(a-f), 113986, 114060, 114067(a,d,e,j), 114069(a, c, d), 114077, 114089.1(c), 114143(c,e))”

36. Equipment / Utensils approved; installed, clean, good repair, capacity.

Conditions Observed: Observed mold-like substance in ice machine. Clean and sanitize ice machine per manufacturer’s directions to prevent mold growth.

ROACHY SAYS:

“Utensils and equipment shall be kept fully operative and in good repair. All new and replacement equipment shall be properly installed and be certified or classified for sanitation by an ANSI accredited certification program. Electrical appliances must meet UL standards. Single-use articles shall not allow migration of deleterious substances or impart colors, odors, or tastes to food. Multi-use food contact surfaces must be smooth, free of breaks, chips, and similar imperfections; free of sharp internal angles, corners, and crevices; finished to have smooth welds and joints; be accessible for cleaning and inspection. Unless specified, wood and wood wicker may not be used as a food-contact surface. Unless specified, copper and copper alloys such as brass may not be used in contact with a food that has a pH below six or for a fitting between a backflow preventer and a carbonator. Beverage tubing and cold-plate beverage cooling devices cannot be installed in contact with stored ice intended to be used as food. Equipment that is not movable must be installed to allow for cleaning in place. Cutting or piercing parts of can openers must be readily removable. Facilities that wash, rinse, soak, thaw, or similarly prepare foods shall be provided with a approved food preparation sink. Reservoirs that supply water to produce foggers must be cleaned and maintained. Surfaces such as cutting blocks and boards that are subject to scratching and scoring shall be resurfaced or replaced if they can no longer be effectively cleaned and sanitized. (114130, 114130.1, 114130.2, 114130.3, 114130.4, 114130.5, 114130.6, 114132, 114133, 114137, 114139, 114153, 114163, 114165, 114167, 114169, 114175, 114177, 114180, 114182)”

37. Equipment, utensils and linens: storage and use.

Conditions Observed: Observed bowl used to portion bulk rice stored on top of bulk rice container. Recommend obtaining a utensil with a handle, and store it in the bulk rice container with the handle facing up out of contact with the food to prevent contamination.

ROACHY SAYS:

“Clean equipment, utensils, linens, and single-use articles shall be stored at least six inches above the floor in an approved location within the fully enclosed permitted food facility. Clean equipment, utensils, linens, and single-use articles shall not be exposed to splash, dust, vermin, or other forms of contamination. Non-food items shall be stored and displayed separate from food and food-contact surfaces. During pauses in food preparation utensils shall be stored with handles above the top of the food, on a clean sanitized surface, in running water, or in water that is at least 135øF. Single-use articles and multiservice utensils shall be handled, displayed, and dispensed so that contamination of food and lip-contact surfaces is prevented. Extra preset tableware shall be removed when a consumer is seated or cleaned and sanitized before further use. Pressurized cylinders shall be securely fastened to rigid structure. Linens must be free of food residue and soil and be laundered as required. (114074, 114075(a,b,d,e), 114081, 114119, 114121, 114161, 114172, 114178, 114179, 114083, 114185, 114185.2, 114185.3, 114185.4, 114185.5)”

44. Premises; personal/cleaning items; vermin-proofing.

Conditions Observed: The facility is to remain vermin proof at all times. Observed door propped open during the entire inspection. Keep the door closed at all times to prevent entrance or harborage of animals, birds, or vermin, including but not limited to, insects and rodents, or install a screen.

ROACHY SAYS:

“All premises of a food facility shall be kept clean, fully operative, and in good repair. The premise of a food facility shall be free of litter and items unnecessary to the operation of the facility. Areas designated for employees to eat and drink shall be located so that food, clean equipent and utensils, linens, and single-use articles are protected from contamination. Personal items shall be stored in a designated area to prevent contamination of food or utensils. Food prep sinks, warewashing sinks, and handwashing sinks shall not be used for the cleaning or maintenance of tools or cleaning supplies or to dispose of mop water and similar liquid wastes. A dedicated janitorial sink with a drain shall be provided and conveniently located. A separate room, area, or cabinet shall be provided for cleaning supplies. The facility shall be kept vermin proof. Insect electrocution devices shall retain the insect within the device and shall not be located over food or utensil handling areas. (114123, 114143(a, b), 114256, 114256.1, 114256.2, 114256.4, 114257, 114257.1, 114259, 114259.2, 114259.3, 114279, 114281, 114282)”

45. Floor, walls, and ceilings: built, maintained, clean.

Conditions Observed: Observed floor and coving is failing throughout the facility. Repair/replace floors to provide a surface that is smooth, durable, nonabsorbent and easy to clean. Submit manufacturer specification sheets or floor samples to this office for approval prior to purchase and installation.

ROACHY SAYS:

“Food facilities shall be fully enclosed in a building consisting of permanent floors, walls, and an overhead structure that meets minimum standards. The walls and ceiling shall be smooth, durable, nonabsorbent, and easily cleanable. Flooring and base coving shall be smooth, durable, and made of approved nonabsorbent material that is easily cleanable. Floor surfaces shall be coved at the juncture of the floor and wall with a 3/8 inch minimum radius and shall extend up the wall at least 4 inches. (114143(d), 114266, 114268, 114268.1, 114271, 114272)”

Routine Inspection
28. Food separated and protected.

Conditions Observed: Observed open bulk bag of sugar on storage shelf. Once a bulk bag of food is opened, transfer it to a rigid container with a tight fitting lid to protect bulk foods from contamination.

ROACHY SAYS:

“Food shall be protected from contamination during transportation, storage, preparation, holding, and display. Adequate and suitable counter space shall be provided for all food preparation. Food preparation shall be conducted wthin an approved food compartment or fully enclosed food facility. Open-air barbecues shall be separated from public access. (113984(a-f), 113986, 114060, 114067(a,d,e,j), 114069(a, c, d), 114077, 114089.1(c), 114143(c,e))”

36. Equipment / Utensils approved; installed, clean, good repair, capacity.

Conditions Observed: Observed mold-like substance in ice machine. Clean and sanitize ice machine per manufacturer’s instructions. Keep this piece of equipment on a regularly cleaning and maintenance schedule to prevent mold growth. Observed unapproved utensil (bowl), being used to portion bulk rice. Obtain an approved utensil, with a handle that is smooth, durable, nonabsorbent and easy to clean. Store with handle facing up, out of contact with the food.

ROACHY SAYS:

“Utensils and equipment shall be kept fully operative and in good repair. All new and replacement equipment shall be properly installed and be certified or classified for sanitation by an ANSI accredited certification program. Electrical appliances must meet UL standards. Single-use articles shall not allow migration of deleterious substances or impart colors, odors, or tastes to food. Multi-use food contact surfaces must be smooth, free of breaks, chips, and similar imperfections; free of sharp internal angles, corners, and crevices; finished to have smooth welds and joints; be accessible for cleaning and inspection. Unless specified, wood and wood wicker may not be used as a food-contact surface. Unless specified, copper and copper alloys such as brass may not be used in contact with a food that has a pH below six or for a fitting between a backflow preventer and a carbonator. Beverage tubing and cold-plate beverage cooling devices cannot be installed in contact with stored ice intended to be used as food. Equipment that is not movable must be installed to allow for cleaning in place. Cutting or piercing parts of can openers must be readily removable. Facilities that wash, rinse, soak, thaw, or similarly prepare foods shall be provided with a approved food preparation sink. Reservoirs that supply water to produce foggers must be cleaned and maintained. Surfaces such as cutting blocks and boards that are subject to scratching and scoring shall be resurfaced or replaced if they can no longer be effectively cleaned and sanitized. (114130, 114130.1, 114130.2, 114130.3, 114130.4, 114130.5, 114130.6, 114132, 114133, 114137, 114139, 114153, 114163, 114165, 114167, 114169, 114175, 114177, 114180, 114182)”

37. Equipment, utensils and linens: storage and use.

Conditions Observed: Observed utensil stored in steamed rice inside of rice cooker. Obtain a sanitary container to store rice utensil in to prevent contamination.

ROACHY SAYS:

“Clean equipment, utensils, linens, and single-use articles shall be stored at least six inches above the floor in an approved location within the fully enclosed permitted food facility. Clean equipment, utensils, linens, and single-use articles shall not be exposed to splash, dust, vermin, or other forms of contamination. Non-food items shall be stored and displayed separate from food and food-contact surfaces. During pauses in food preparation utensils shall be stored with handles above the top of the food, on a clean sanitized surface, in running water, or in water that is at least 135øF. Single-use articles and multiservice utensils shall be handled, displayed, and dispensed so that contamination of food and lip-contact surfaces is prevented. Extra preset tableware shall be removed when a consumer is seated or cleaned and sanitized before further use. Pressurized cylinders shall be securely fastened to rigid structure. Linens must be free of food residue and soil and be laundered as required. (114074, 114075(a,b,d,e), 114081, 114119, 114121, 114161, 114172, 114178, 114179, 114083, 114185, 114185.2, 114185.3, 114185.4, 114185.5)”

© 2024 Lost Coast Communications Contact: news@lostcoastoutpost.com.